Wednesday, May 9, 2012
Maintenance of your General Lawn Mower
You wish to keep your lawn healthy, green and abundant all year long, and your lawn mower is a crucial part of maintaining your lawn's general health and charm. By using these tips on general lawn mower upkeep, you will ensure that your lawn mower is operating at maximum efficiency whenever you should employ it.
Tip #1
Always maintain your lawn mowers edge sharp. A wear out lawn mower blade tends to make an twisted cut to your lawn, and may even ruin your grass. Additionally, a clear , crisp edge means trimming efficiency, lessening deterioration of your lawn mower's engine along with other parts.
Tip #2
Make certain your lawn mower's air filter is clean and without any dust particles and dirt. You can usually just shake the air filter away to remove dust and debris. However if your air filter has been utilized for some time, and it has many build-up on it you need to change it out promptly. All of your current lawn mower's parts operate in line with one another so saving money by not changing a terribly soiled air filter will only cost you money in the end.
Tip #3
Clean your lawn mower's carburetor. Exactly like your vehicle, your lawn mower's carburetor should be looked after. Before detaching the carburetor, make sure the fuel line has been turned off. When you have the carburetor out provide it with a good clean up so that it's floating valve has the ability to move openly. Then replace the carburetor and switch the fuel back again.
Tip #4
Check out your lawn mower's gas. Along with always keeping the gas lead up, to at least halfway, ideally you should change any gas which was remained from the early season that did not have a stabilizer added to it.
Tip #5
Moreover to preserving the gasoline topped up and in excellent condition, ensure that you check out your lawn mower's fuel lines. It's very normal to switch your fuel line off at the conclusion of the season, so it's effortless to leave behind about it. Should your lawn mower is not starting examine that first. When the engine still does not start the fuel may not be arriving at the carburetor. To check that, take away the fuel hose from your carburetor to determine if the gas is flowing through. If it is, you can hook up both. If it is not your fuel line might be plugged or the filtration system may be blocked.
Tip #6
Take a look at the spark plug. That is the most fundamental steps you can take should your lawn mower is not starting up or functional. To determine it, detach the wire towards the end of the plug prior to removing it. You want to guarantee the spark plug is not moist or dirty.The following tips on general lawn mower upkeep help keep your lawn mower performing its task adequately all over the time of year. You will not spend as much on expensive lawn mower repair and part replacement by performing continual servicing on it. Your lawnmower can last much longer, and also your lawn will be a wonderful view to see.
About the Publisher
Blake Bahrns is a lawn mower parts and small engine parts expert with more than 20 years of expertise working on lawn and backyard garden products. For extra lawn mower tips, lawn care tips, and more free lawn mower articles or blog posts go to www.lawneq.com.
Monday, February 15, 2010
Differences Between Toro Walk Behind Recycler Mowers
What's The Difference Between a Toro Model 20330 & Toro Model 20333?
With spring just around the corner you might be looking for a new walk behind mower. Here are a couple of the differences between the different Toro walk behind mower.
Engine:
Model 20330- 6.75 ft-lb Gross Torque Briggs & Stratton w/ Ready Start
Model 20333- 7.0 ft-lb Gross Torque Briggs & Stratton w/ Ready Start
Starter:
Model 20330- Recoil
Model 20333- Recoil w/ BOS
Self-Propel:
Model 20330- Variable Speed
Model 20333- Personal Pace
Blade Override System (BOS):
Model 20330- N/A
Model 20333- Standard
Cutting Width:
Model 20330- 22"
Model 20333- 22"
Deck Material:
Model 20330- Steel
Model 20333- Steel
Height of Cut:
Model 20330- 1.0" - 4.0"
Model 20333- 1.0" - 4.0"
Mulch, Rear Bag, Side Discharge:
Model 20330- Standard
Model 20333- Standard
Washout Port:
Model 20330- Standard
Model 20333- Standard
Handle:
Model 20330- 1 Piece/ Padded
Model 20333- 1 Piece/ Contoured
Wheel Height:
Model 20330- 8"
Model 20333- 8"
Bag On Demand:
Model 20330- N/A
Model 20333- Standard
With spring just around the corner you might be looking for a new walk behind mower. Here are a couple of the differences between the different Toro walk behind mower.
Engine:
Model 20330- 6.75 ft-lb Gross Torque Briggs & Stratton w/ Ready Start
Model 20333- 7.0 ft-lb Gross Torque Briggs & Stratton w/ Ready Start
Starter:
Model 20330- Recoil
Model 20333- Recoil w/ BOS
Self-Propel:
Model 20330- Variable Speed
Model 20333- Personal Pace
Blade Override System (BOS):
Model 20330- N/A
Model 20333- Standard
Cutting Width:
Model 20330- 22"
Model 20333- 22"
Deck Material:
Model 20330- Steel
Model 20333- Steel
Height of Cut:
Model 20330- 1.0" - 4.0"
Model 20333- 1.0" - 4.0"
Mulch, Rear Bag, Side Discharge:
Model 20330- Standard
Model 20333- Standard
Washout Port:
Model 20330- Standard
Model 20333- Standard
Handle:
Model 20330- 1 Piece/ Padded
Model 20333- 1 Piece/ Contoured
Wheel Height:
Model 20330- 8"
Model 20333- 8"
Bag On Demand:
Model 20330- N/A
Model 20333- Standard
Tuesday, February 2, 2010
Punxsutawney Phil The Groundhog
Punxsutawney Phil saw his shadow today which means 6 more weeks of winter...
Whose to say that the rodent knows what he is talking about!! So now is the perfect time to get your mower in & have it ready to go for Spring!!!!!
Give us a call today to get your mower in & have it ready to go for spring. (217) 342-2909. Don't forget that if you are a local customer you will receive FREE pick up & delivery through the month of February. Also, visit us online at www.lawneq.com.
Monday, January 25, 2010
Kubota BX24 or Massey Ferguson GC2310


Which do you prefer Kubota BX24 or Massey Ferguson GC2310?
Below you will find the similarities & differences...
Engine
Engine Gross Power HP
Kubota- 23.0
Massey- 22.5
PTO Power HP
Kubota- 17.7
Massey- 18.7
No. of Cylinders
Kubota- 3
Massey- 3
Total Displacement
Kubota- 54-8
Massey- 68.5
Fuel Tank Capacity
Kubota- 6.6
Massey- 5.5
Transmission
Type
Kubota- HST (2 Ranges)
Massey- HST (2 Ranges)
Brake
Kubota- Multi Wet Disc
Massey- Wet Disc
Hydraulic System
Pump Capacity
Kubota- 6.2
Massey- 6.1
3-Point Hitch Lift Capacity @ 23" Behind Lift Point
Kubota- 680
Massey- INA
Power Steering
Kubota- Hydrostatic Power Steering
Massey- Hydrostatic Power Steering
Generals
Quarter Inching Valve
Kubota- Standard
Massey- N/A
12-V DC Outlet
Kubota- Standard
Massey- N/A
Tachometer
Kubota- Standard
Massey- Standard
Seat Mounted Seat Belt
Kubota- Standard
Massey- N/A
Wednesday, January 20, 2010
How To Install A Fuel Line On An Echo Blower
Below watch Blake show you How To Install A Fuel Line On An Echo Blower. If you have any questions please feel free to contact us at LawnEq.com & 800-432-2909.
Wednesday, January 13, 2010
Importance of Having Your Mower Serviced

It is Important To Have Your Mower Serviced On a Regular Basis
The bottom line to having a charming lawn with healthy grass is keeping you mower in a good working condition. You should make sure that you service your mower & sharpen your lawn mowers blades on a regular basis.
If your lawn mower is maintained it will have an extended lifespan. Another reason to keep up the maintenance of your mower is so that your lawn looks healthy and beautiful. If your mower has dull blades it may cut your lawn unevenly or it might not cut at all. Also, dull blades tear & shred grass which may leave your lawn open to infection & lower it's ability to absorb water & nutrients.
If you are looking for somebody to take a look at your lawn mower contact us. LawnEq.com
Tuesday, January 12, 2010
What's The Difference Between Kubota RTV1100 & Polaris Ranger?

What's The Difference Between
Polaris Ranger?
ENGINE
Make
Kubota- Kubota
Polaris- Fuiji
Type
Kubota- 4-cycle diesel
Polaris- 4-cycle gas
Cylinders
Kubota- 3
Polaris- 1
Displacement (cc)
Kubota- 1123
Polaris- 499
Horsepower
Kubota- 24.8 hp @ 3000 rpm
Polaris- 30 hp
Max Torque (ft-lbs)
Kubota- 50.6
Polaris- --
Fuel Tank Capacity
Kubota- 7.9 Gallons
Polaris- 9.0 Gallons
Muffler
Kubota- Spark Arresting
Polaris- Spark Arresting
Alternator
Kubota- 75 amps
Polaris- 250 watts
TRANSMISSION
Type
Kubota- Variable Hydrostatic Transmission (VHT)
Polaris- CVT with Belts
Wheels, Drive System
Kubota- Rear 2WD or 4WD
Polaris- Rear 2WD or 4WD
Differential Lock
Kubota- Standard, Foot Operated
Polaris- Front- on/ off switch rear hand operated
Gear Selection
Kubota- Hi-Med-Lo Range Forward, Neutral & Reverse
Polaris- Hi-Lo Range Forward, Neutral , Reverse
Steering
Kubota- Power
Polaris- Manual
BRAKES
Front
Kubota- Sealed Hydraulic Discs
Polaris- Hydraulic Disc
Rear
Kubota- Sealed Hydraulic Discs Rear Wheel, Hand Lever
Polaris- Hydraulic Disc
Parking
Kubota- Sealed Hydraulic Discs Rear Wheel, Hand Lever
Polaris- Rear, Foot Operated
SUSPENSION
Front
Kubota- Independent, McPherson Struts
Polaris- Independent, McPherson Struts
Rear
Kubota- Semi-Independent, DeDion Axle w/Leaf Springs & Hydraulic Shocks
Polaris- Independent
Occupant Protection System
Kubota- 2.0" Steel Tube; meets OSHA 1928.53 & SAE J2194 ROPS
Polaris- Steel Tube ROPS
Factory- Installed Integrated Full Cabin
Kubota- Standard
Polaris- Not Available
Factory Air Conditioner & Heater
Kubota- Standard
Polaris- Not Available
Speaker System
Kubota- Standard
Polaris- ---
Standard Pre-Wiring For Optional AM/FM/ CD Player
Kubota- Standard
Polaris- Not Available
Monday, January 11, 2010
Be Careful Using Your Chainsaw This Winter

Be Careful Using Your
Chainsaw This Winter
When using your chainsaw this winter be extra careful. You need to be aware that the ground is probably frozen & could be very slick. Be sure you have good footing with good traction.
When you are working with your chansaw during the winter months to come be sure to wear all your protective equipment. You should always wear hearing protection, gloves, helmet & eye protection. In the winter months the wood is even more likely to splinter. It would be a good idea to wear protective pants to if you have some. These pants are made with materials that are both cut-retardant and resistant to water & snow.
With all chainsaw winter work take an extreme precautions and Be Careful out there!!
Labels:
chainsaws,
precautions,
Stihl chainsaws,
winter chainsaw use
Wednesday, January 6, 2010
How To Change The String On An Echo Bump Head Trimmer
Above you can watch Blake with LawnEq.com show you How To Change The String On An Echo Bump Head Timmer. Blake will show you step by step instructions on how to do this. He makes this task quick & simple just for you.
Tuesday, January 5, 2010
Lawn Mower Racing Rules
Are You Ready to Start Racing Your Lawn Mower? It's Time To Start Getting Your Mower Ready For The Upcoming Racing Season!!!
And You Need To Know The Rules...
Lawn Mower Racing Rules
Personal Safety (All Classes)
* Helmet
* Eye Protection (Goggles or Full Face Helmet)
* Full Shoes or Boots
* Gloves
* Long Pants
* Long-Sleeve Shirt
Tractor Safety (All Classes)
* Throttle: Spring Return To Idle
* Engine Kill Switch Tethered To Driver
* Good Working Breaks (Trans or Axle)
* Driver Must Stay Seated
* Battery Must Be Secure
* Fender & Foot Rest Must Be Attached & Form A Barrier Between Driver & Wheels
* Maximum 38" Width
* Exhaust Must Exit To The Rear
* Maximum RPM: 4500 Governed Engines Vertical Shaft
* Open Steering Built With Safety In Mind
RULES SUBJECT TO CHANGE FOR SAFETY OR COMPETITION FAIRNESS ONLY BY MAJORITY VOTE
Stock Class
* Engine, Trans, & Front Axle Must Be Mounted In Original Locations
* Gear Drive Trans Axle Only With The Pulley On Top 31 Series Briggs & Stratton or Smaller Single Cylinder Only
* Engine & Trans Pulleys Must Be In The Same Plane
* Racer Must Derive From A OEM Mower Chassis
* You may Lock Rear Axle
* Front Axle Must Be Welded To The Frame
* Must Use Original Front J Spindles
* Minimum 4" Ground Clearance (Exhaust May Be Lower)
* Rear Tire Size Must be 16" Through 23" Lawn & Garden Tire Only
* Front Rim Minimum of 6"
* Engine Must Be Stock Except You May Do Headwork
Modifeid Class
* Engine Must be 24 HP or Lower
* Engine In Original Location on Frame
* Stock Wheelbase + or -4"
* Majority Of The Frame Must Be OEM
Tuesday, December 29, 2009
Are you Looking For a New Toro Snow Blower?

Are you Looking For a New Toro Snow Blower?
What about a new Toro CCR 2450 GTS?
Here is all you need to know about this nice snow blower...
Engine
Engine: Toro R*Tek 2-Cycle
Displacement: 141 cc
Starting System: Recoil
Fuel Capacity: 1.0 Quart
Transmission
Ignition: Electronic
Dimensions
Capacity: Up to 1,700 lbs per minute
Throwing Distance: Up to 30'
Clearing Width: 20"
Weight: 71 pounds
General Info
Auger: Power Curve Rotor
Wednesday, December 23, 2009
Where are you on Santa's List?

Where are you on Santa's list?
Have you been Naughty or have you been Nice this year???
What is on your Wish list for Santa this year??
Maybe a new chainsaw or a new Kubota RTV or a new trimmer or a new push mower, what will Santa bring you this year??
We here at Bahrns Equipment, Inc. & LawnEq.com Hope You Have a Very Merry Christmas & A Happy 2010!!!!
We hope that Santa brings you all that you wish for!!!!
Labels:
chainsaws,
kubota RTV. kubota,
lawn mowers,
mowers,
push mowers,
string trimmer,
trimmers
Tuesday, December 22, 2009
What's The Difference Between The Toro Power Shovel & 1800 Power Curve?

What's the difference between the Toro Power Shovel & 1800 Power Curve??
Capacity
Power Shovel- 300 lbs.
1800 Power Curve- 700 lbs.
Throw Distance
Power Shovel- Up to 20'
1800 Power Curve- Up to 30'
Clearing Width
Power Shovel- 12"
1800 Power Curve- 18"
Drive System
Power Shovel- Poly V Belt
1800 Power Curve- Poly V Belt
Rotor Style
Power Shovel-2 Blade Curved Rotor
1800 Power Curve- 2 Blade Curved Rotor
Snow Cut Depth- 1 Pass
Power Shovel- 6"
1800 Power Curve- 10"
Amps/ Motor
Power Shovel- 7.5 Amp/ Series- Wound
1800 Power Curve- 12 Amp/ Series- Wound
Directional Control
Power Shovel- N/A
1800 Power Curve- 180 Degree Chute Crank
Throw Height Control
Power Shovel- N/A
1800 Power Curve- Deflector
Best Usage
Power Shovel- Sidewalks, Decks & Small Driveways
1800 Power Curve- Larger Driveways & Walkways
Tuesday, December 15, 2009
Comparison of Echo Chainsaw~ CS-370 & CS-600P

Ever wonder what the difference in Echo chainsaws, CS-370 & CS-600P?
We are going to let you know now.
Engine Displacement (cc)- 36.3
Engine Displacement (cu in)- 2.21
Starting System- i-30
Ignition System- Digital
Carburetor )w/Purge Pump)- Butterfly-Valve Diaphragm
Oiling System- Automatic/ Adjustable
Vibration Reduction System- Standard
Available Bar Lengths- 14, 16 & 18
Fuel Capacity (fl. oz.)- 13.9
Oil Capacity (fl. oz.)- 9.5
Dry Weight (lb)- 10
CS-600P
Engine Displacement (cc)- 59.8
Engine Displacement (cu in)- 3.65
Starting System- Standard
Ignition System- Digital
Carburetor (w/Purge Pump)- Butterfly-Valve Diaphragm (without Purge Pump)
Oiling System- Automatic/ Adjustable (Clutch-Driven)
Vibration Reduction System- Standard
Available Bar Lengths- 20, 24 & 27
Fuel Capacity (fl oz)- 19.1
Oil Capacity (fl oz)- 10.1
Dry Weight (lb)- 13
Labels:
chainsaws,
cs-370,
cs-600p,
Echo chainsaw,
echo cs-370,
echo cs-600p
Monday, December 14, 2009
Echo CS-8000 Chainsaw

Echo CS-8000 Chainsaw
This chainsaw is Echo's largest chain saw that delivers professional quality, reliability and performance for your toughest applications.
This Echo CS-8000 Chainsaw Features:
* 80.7 cc High Performance, 2-Stroke Engine
* Available in 24", 27", 32" & 36" bar lengths
* Replaceable bumper spike improve control for easier cutting
* Slope Advance Ignition System automatically adjusts ignition timing for optimum performance
* Cushioned left-hand grip
* Automatic, adjustable oiler with manual over-ride
Specifications:
Engine Displacement (cc)- 80.7
Engine Displacement (cu in)- 4.92
Starting System- Standard
Ignition System- SAIS
Carburetor (w/Purge Pump)- Butterfly-Valve Diaphragm (without Purge Pump)
Oiling System- Automatic/ Adjustable (with manual override)
Vibration Reduction System- Standard
Available Bar Lengths (in)- 24, 27, 32 & 36
Fuel Capacity (fl. oz.)- 28.9
Oil Capacity (fl oz.)- 14.1
Dry Weight (lbs)- 16.5
Labels:
chainsaws,
cs-8000,
Echo chainsaw,
echo chainsaw cs-8000
Thursday, December 10, 2009
Illinois Changes Law on Insurance of All-Terrain Vehicles

Illinois Changes Law on Insurance of All-Terrain Vehicles As Of January 1, 2010
The General Assembly of Illinois has enacted legislation requiring liability insurance coverage of any "non-highway vehicle" used on Illinois roadways. In accord with the newly-adopted provision of the Illinois Motor Vehicle Code (625 ILCS 5/11-1426.1), any person operating a "non-highway vehicle" on a street, highway or roadway is now subject to the state's mandatory insurance requirements, just like automobiles.
For purposes of the law, a "non-highway vehicle" means a motor vehicle not specifically designed for use on a public highway, including the following:
1. An all-terrain vehicle
2. A golf cart
3. An off-highway motorcycle
4. A neighborhood vehicle. A neighborhood vehicle, as defined in 625 ILCS 5/1-148.3m, means a self-propelled, electronic-powered, four-wheeler motor vehicle (or a self-propelled, gasoline-powered, four-wheeled motor with an engine displacement under 1,200 cubic centimeters) that is capable of attaining a speed of more than 20 miles per hour, but not more than 25 miles per hour, and which conforms to federal regulations under Title 49 C.F.R. Part 571.500.
The law also requires that an insurance card or policy Declarations page establishing proof of coverage must be presented to any law enforcement officer stopping one of these vehicles on a public roadway and requesting proof of insurance. Failure to produce the insurance card may subject the operator to a suspension of your automobile operator's license and/or a fine.
YOUR RESPONSIBILITIES
The law requires you to have a "non-highway vehicle" insured for liability losses if operated on a public roadway. This would include a "non-highway vehicle" operated on a highway right-of way. You are strongly encouraged to immediately contact your insurance agent and inquire whether your "non-highway vehicles" are insured by such a policy or endorsement. Please provide a description of your "non-highway vehicle" and serial numbers to your agent.
If your "non-highway vehicles" have been properly insured, your agent will issue an insurance card for you to produce if stopped by a police officer on a public roadway.
Monday, December 7, 2009
Lawn Mower Race
Lawn Mower Race
Recently one of our very own mechanics, Jake Devall was involved in a lawn mower race at Post Oak near St. Elmo, IL. Jake had a great time being involved in this event. He brought home the gold and won 1st place in this race. Way To Go Jake!!!!
Jake has been a mechanic here at Bahrns Equipment, Inc. since May of 2007. He lives here in Effingham & is a graduate of Effingham High School. Jake often enters varies lawn mower races around the area.
Recently one of our very own mechanics, Jake Devall was involved in a lawn mower race at Post Oak near St. Elmo, IL. Jake had a great time being involved in this event. He brought home the gold and won 1st place in this race. Way To Go Jake!!!!
Jake has been a mechanic here at Bahrns Equipment, Inc. since May of 2007. He lives here in Effingham & is a graduate of Effingham High School. Jake often enters varies lawn mower races around the area.
Wednesday, December 2, 2009
Sledding

Do you remember waiting and waiting as a kid for the snow to come? I know I did. I couldn't wait for the snow to fall because that meant I got to go sledding. There is nothing better than that!!! We would hit all the big hills and my uncles would take us on this 4-wheeler all over the place.
My uncle now has a Kubota RTV that he ties the sled up to and takes all the kids for sled rides. My son can't wait for another year at Uncle Jr's house to play in the snow.
Those are memories that will last forever!!!
December Is Here

Well December has arrived and we have almost made it through 2009. Although yesterday, the 1st of December sure didn't feel like a normal December day with it being 55 degrees outside.
I think we will soon be visited by Ol'Man Winter. It will soon be snowing & blowing & icing. Let's hope that we do not get any bad ice storms this year. In case we do it would be good to have a generator on hand in case the power goes out. Also, if you have a fireplace it would be good to have a Stihl chainsaw on hand to cut fire wood to keep on hand.
I hope that everyone has a safe winter season!!
Wednesday, November 25, 2009
Be Thankful This Thanksgiving

Thanksgiving is a time to reflect on all that we have to be thankful for. Our freedom, our family and our friends are a good start. As we go into this holiday season we need to slow down and take the time to enjoy what we have. As we prepare to go into the frenzy of the holiday shopping and parties remember that we shouldn’t take any moment for granted.
If you are like I am, the holiday shopping wouldn’t be so bad if it weren’t for the crowded stores and the lack of parking. The hustle and bustle is to some one of their favorite parts of Christmas. I on the other hand could do without that part of it. This time of year, or any time of year for that matter if you need a part for your chainsaw, or your snow blower, or your generator, why not avoid getting out at all. Use our handy online ordering and have the part shipped to your door. Let your mail carrier get out in the weather and you can order your part and sit back and wait for it to be delivered. Just one more thing to be thankful for.
My wish for all is a wonderful Thanksgiving, followed by a Merry Christmas and/or Great Holiday, and of course a Very Happy New Year.
If you are like I am, the holiday shopping wouldn’t be so bad if it weren’t for the crowded stores and the lack of parking. The hustle and bustle is to some one of their favorite parts of Christmas. I on the other hand could do without that part of it. This time of year, or any time of year for that matter if you need a part for your chainsaw, or your snow blower, or your generator, why not avoid getting out at all. Use our handy online ordering and have the part shipped to your door. Let your mail carrier get out in the weather and you can order your part and sit back and wait for it to be delivered. Just one more thing to be thankful for.
My wish for all is a wonderful Thanksgiving, followed by a Merry Christmas and/or Great Holiday, and of course a Very Happy New Year.
Subscribe to:
Posts (Atom)


